Deliberant APC Firmware Release Notes
From Deliberant wiki
Contents |
Version 5.78-1
What's new in 5.78-1 firmware release
- Added BA window size control to STA GUI for station & station wds mode
- Minimum transmit power 0 dbm
Fixes
- Fixed maximum transmit power calculation on Slave/Station
- Fixed 20MHz/SISO low throughput issue
- Fixed bug at fs/proc/generic.c:732 remove_proc_entry()
- Fixed LACP packets pass-through problem
- Fixed DHCP client when bridge mode uses incorrect mac address
- Fixed GUI when sometimes does not start DHCP client
Version 5.78
What's new in 5.78 firmware release
- Vendor & distributor disclaimer (appears after every reset to factory defaults)
- Added CT (Compliance Testing) country code, which disables all regulatory limits
- LAN PoE tab instead of LED on FWBD-0120
- Formula to calculate max EIRP for Canada and USA in 5725-5850 MHz
- Additional TX power limits for 2 GHz products
Fixes
- Fixed iPoll problem when traffic stops being passed on Master.
- Fixed IE8/9 problem which does not let to upgrade firmware
- iPoll autotune enabled on Master radio by default (STA does not have "Tx queue lengt")
- GUI supports G/N mixed in IEEE mode list
- Fixed Station WDS mode instead of Station because of wds.status=enabled in default configuration
- Fixed message about VAP changes when iPoll is turned on
Version 5.77
General
- Added VLAN tagging support
- Added Multiple BSSID support. GUI allows to create 3 Virtual AP's
- Added auto channel feature
- Added MAC change feature on wireless and wired interfaces
- Added GUI High contrast mode for easy devices outdoor configuration when sun is shining brightly
- Added option to upload product file from GUI
- Added delayed reboot feature (useful for configuring link remotely with instant changes)
- Added ping tool
- Added option to disable/enable SSH and option to change SSH port
- Added new tab in Status section with ARP info (ARP table)
- Added new tab in Status section with Routes info (Route table)
- Added option to disable data rate fallback
- Added option to control external LED's (LAN, Power and RSSI LED is controlled separately)
- Added DMZ feature for NAT'ed router mode. All incoming traffic which is not defined in Port forwarding rules is redirected to the defined IP
- Added UPnP feature. DMZ and UPnP cannot work at the same time. If DMZ feature is enabled, UPnP is disabled.
- Added option to limit traffic per IP in Access Point mode
- Added option to change web page login username via GUI
- Added Traceroute tool
- Added DHCP leases statistics (only in router mode with DHCP server on LAN side)
- Added option to enter IP alias
- Added spaces support in WPA passphrase
- Added option to change HTTP port
- Added OpenVPN feature (no controls in GUI)
- Added DNSMASQ service. Service will be enabled when DHCP server is ON and DNS server IP is the same as LAN IP
- Added peer MAC information on GUI in CPE mode
- Added worldwide regulatory domain database (DB) to driver (frequency and TX power limitations for each country)
- Added option to limit TX power via product file
- Added DFS support
- Added WXEE support for calculating received signal level
- Added WXEE support for getting TX power calibration information and max real output power
- Added spectrum analyzer tool
- Added option to set antenna Gain in GUI
- Added option to change beacon radio parameters for faster TX power testing
- Added Proprietary wireless protocol - iPoll
- Added Adaptive modulation (Auto rate)
- Added Intelligent Access Point Auto-WDS mode
- Added Smart auto channel
- Added A-MSDU support
- Added Automatic TX power control (ATPC)
- Added Device state information from WNMS agent
- Added UAM (Web portal authentication) support for 2 GHz units working in router mode
- Added static routes in bridge mode
- Added Wireless client L2 isolation
- Added Reset tool support
Improvements
- Improved statistics showing in Status section. Statistics tab split into Network and Wireless tabs
- Improved scan feature for Station mode in Configuration->Wireless tab. Pointing over desired SSID a tool-tip shows up with MAC, Signal level and Security info
- Improved WDS mode: added support to connect to Ubiquity and Mikrotik devices with WDS mode enabled
- Improved device branding during manufacturing. Added option to change default configuration file without FW upgrade
- Improved internal instant changes handling algorithm
- Improved site survey scanning result display time. Removed static waiting time, now waiting time depends on how many channels are scanned
- Improved wireless ACL: GUI supports MAC masking feature
- Improved Wireless statistics status information listing on WEB configuration page
- Improved VLAN configuration: allows configuring management VLAN on the same radio interface which has the data VLAN
- Improved Wireless ACL layout in GUI
- Improved VAP radio interfaces layout in GUI
- Improved Information | Wireless page tab in AP mode
- Improved delayed reboot tool. Added remaining time till reboot indication
- Improved performance in general
- Improved maximum allowed wireless client count from 31 to 127
- Improved ARP-NAT functionally by allowing to pass-through VLAN tagged traffic
- Improved Smart "Scanned SSID" filtering in Configuration -> Wireless section
- Improved configuration file version support
- Reduced message max age for bridge network mode
- Improved Ping tool: add packet size field validation
- Improved static routes configuration
- Improved statistics mechanism
- Improved Comply regulations usability
- Extended VAP count up to 7
- Improved message when applying link settings
- Improved error message when setting empty username or password
- Improved PPPoE settings in status tab
- Improved Spectrum analyzer in all products
- Improved Static routes configuration
- Improved Ebtables rules handling when peers are connected
- Improved instant change failure timeout - increased to 40 seconds
